CV-2 Grease
-
Outperforms the best conventional or synthetic greases and lubes
-
Withstands extreme temperature and pressure in wheel bearings, U-joints, and high-angle CV Joints
-
Excellent high-temp stability, extreme-pressure protection, and water resistance
-
Used in a variety of applications with operating temps from -100°F to 500°F
-
Strong resistance to oxidation and corrosion, low evaporation and oil separation with a minimum effect on rubber seals
-
Contains an organic moly for chassis lubrication and high temp/high speed industrial equipment
-
Synthetic fluidity allows increases in bearing life up to 200%
-
Will darken after high-temp use-not detrimental to performance
ABOUT RED LINE GREASE AND ASSEMBLY LUB
-
Used by many of the best engine builders, engineers, and technicians in Formula 1, GP2, Formula 3, NASCAR, NHRA, and WRC
TYPICAL PROPERTIES
4-Ball Wear (ASTM D-4172B): 0.46
4-Ball Weld (ASTM D-2783): 400 Kg
Load/Wear Index (ASTM D-2783): 71.1
Drop Point: 900°F+
MORE TECHNICAL INFORMATION
Lubricant 4-Ball Wear Load/WearIndex
(ASTM D-4172B) (ASTM D-2783)
Red Line CV-2 0.46 71.1
Syn Grease - M 0.50 41.9
Syn Moly Grease - A 0.78 38.4
GM Wheel Bearing Grease 0.71 36.6
Lubricant 4-Ball Weld Drop Point
(ASTM D-2783)
Red Line CV-2 400 Kg 900°F+
Syn Grease - M 2 200 Kg 485°F
Syn Moly Grease - A 315 Kg 515°F
GM Wheel Bearing Grease 250 Kg 525°F
PROPERTY CV-2 GREASE
NLGI Grade #2
NLGI Service GC-LB
Thickener Non-Soap
Fluid Type Thermally-stable synthetic
Useful Temperature Range -100°F to 500°F
Color Red
Dropping Point, °F 900+
Load Wear Index 71.2
4-Ball Wear Scar Diameter (Red), 40 Kg 0.46 mm
Water Washout @ 105°F 1%
Evaporation Loss, 22 hrs @ 350°F 4%
Oil Separation, 30 hrs @ 350°F 5%
Oxidation Stability, 500 hrs @210°F, psi 12
Rust Test, ASTM D1743 Pass
Red Line CV-2 Grease is designed to withstand the extreme temperatures and pressures
which occur in high-performance wheel bearings and CV-joints. The excellent hightemperature
stability, extreme-pressure protection, and water resistance enables it to
out-perform even the best conventional or synthetic greases. Red Line CV-2 Grease can be
used in a wide range of applications at temperatures ranging between -100°F to 500°F and
provides good oxidation and corrosion resistance, low evaporation and oil separation, and has
a minimum effect on rubber seals. The exceptional extreme-pressure performance and the
fluidity of the synthetic oil allows increases in bearing life of 200% to 800%. Red Line CV-2
Grease contains a red moly compound which is a superior lubricant to black moly disulfide
lubricants.
Red Line CV-2 Grease may also be used in industrial applications such as high-temperature
alternator bearings, high-speed ball bearings, conveyor bearings, worm gear drives, servo
mechanisms, and applications where vibrations can cause fretting wear and corrosion to take
place.
Red Line CV-2 Grease will retain its consistency and extreme-pressure performance under
high-temperature and high-shear conditions for extended periods, which extends the
performance ranges of the lubricated components. Red Line CV-2 will slightly darken after
high-temperature use; this darkening will not detrimentally effect the performance of the
grease. Although Red Line CV-2 is compatible with small amounts of many petroleum-based
greases, it is always good lubrication practice to thoroughly clean out the old grease to
eliminate abrasive particles and to minimize the possibility of grease incompatibility.
|