Extreme PSI :: Fuel Components :: Fuel Hangers :: Radium Engineering Fuel Pump Hanger: Mitsubishi Evolution VIII & IX 2003-2006

Follow us:
FacebookTwitterInstagramLinkedinGoogle PlusYoutube


<< Manley Performance Clearance Sale! >>

ACT SALE! 30% OFF MSRP ON ALL ADVANCED CLUTCH PRODUCTS WHILE SUPPLIES LAST!

 

Radium Engineering Fuel Pump Hanger: Mitsubishi Evolution VIII & IX 2003-2006 #32303

Radium Engineering Fuel Pump Hanger: Mitsubishi Evolution VIII & IX 2003-2006 #32303

Radium Engineering Fuel Pump Hanger: Mitsubishi Evolution VIII & IX 2003-2006
 
(0 reviews)  

Click here to download installation instructions (PDF)

The Radium Engineering fuel pump hanger allows the use of 1 or 2 aftermarket pumps in the stock Mitsubishi Evo 8-9 fuel tank.

This system is ONLY compatible with Walbro pumps (Ti Automotive F90000267, F90000274 and F90000285) and the short AEM 50-1220 E85 pumps. The machined assembly drops-in the factory fuel tank replacing the OEM hold-down flange. A single 8AN male pump feed port and 6AN male return port simplify aftermarket -AN hose plumbing. However the preassembled adapter fittings are compatible with the OEM fuel lines.

The custom designed stainless electrical studs easily handle the high current demand that compact bulkhead connectors lack. These serviceable connections are properly sealed and impervious to all standard and exotic fuels. The low profile design keeps all wiring tucked nicely underneath the OEM cover plate. Nonconductive acorn nuts are provided to prevent any accidental short circuits. Furthermore, the high quality in-tank wiring is insulated with chemically resistant PTFE. Electrical hardware is included for the fuel pump(s) and OEM level sender.

One major issue with the OEM EVO 8-9 fuel pump hanger is the restrictive return port and venturi jet pump. When using aftermarket high-flow fuel pumps, the OEM jet pump becomes too restrictive creating unwanted backpressure in the regulator return line causing excessive fuel rail pressure. The Radium fuel pump hanger includes a venturi jet pump with a new integrated pressure-relief valve to minimize back pressure.

All returning fuel from the pressure regulator and crossover hose exit the jet pump keeping the OEM gas tank baffle full for starvation protection.

Single pump applications can reuse the OEM fuel pump controller wiring, but it is recommended to upgrade the OEM wiring as these high flow fuel pumps draw additional current requiring larger gauge wire. Fuel pump wiring kits can be purchased HERE. Select qty1 for single pump applications and qty 2 for dual pump applications.

Features

  • Anodized Aluminum Mounting Plate
  • Venturi Jet Pump with Pressure Relief Valve
  • -8AN Male and OEM Compatible Pump Outlet Fittings
  • -6AN Male and OEM Compatible FPR Inlet Fittings
  • Anodized Aluminum Dual Pump and Fuel Sender Bracket
  • Electrical Hardware for Fuel Pumps and OEM Sender
  • Fluorosilicone Duckbill Return Valve
  • Submersible Rubber Fuel Hose
  • Stainless Steel Hardware and Clamps

 

Pump Configuration Selection

 

If supplying your own pumps, select the option "Pumps Not Included" from the menu. 
Notes:
1. There will be enough components included with this option to use 1 or 2 fuel pumps. Depending on the setup, some parts will simply not be used
.
2. A pliable fuel pump filter sock must be used for proper fitment.

If pumps are included, the kit will come preassembled and 65 micron sock filters will be installed on all fuel pumps. This kit eliminates the OEM hanger's "post" fuel pump filter. A low micron aftermarket fuel filter should be installed downstream to protect the injectors from debris. NOTE: the optional fuel hanger plumbing kits listed below include this necessary post pump filter.

Optional Plumbing Kit

20-0376-0X FUEL HANGER PLUMBING KIT, EVO 8-9 
The plumbing kits include everything required to connect directly to an aftermarket (-8AN male) fuel rail and (-6AN male) FPR for both single and dual pump configurations.  The includes a pre-made PTFE -8AN feed line from the hanger up to the engine bay and the kit re-uses the factory feed line as the regulator return line.

  • PTFE -8AN hoses attach to a Radium Engineering fuel filter that mounts underneath the vehicle using a specifically designed EVO 8-9 bolt-on bracket.
  • Depending on the kit selected (-01,-02,-03), the fuel filter will be assembled with 1 of 3 different elements. Go HERE for more filter element information.

INCLUDES

  • Fuel Filter (-01 Cellulose, -02 Microglass, or -03 Stainless)
  • Black 8AN Male Adapter Fittings (x2)
  • Billet Aluminum 60mm Filter 2-Piece Clamp
  • Aluminum EVO 8-9 Filter Bracket
  • 8AN PTFE Fuel Feed Hose Replacement (x2)
  • 6AN PTFE Fuel Return Replacement
  • Vapor Shield Hose, 6AN ORB Fitting, and EFI Clamp
  • Inverted Flare to 6AN Adapter Fitting
  • Stainless Steel Hardware
5%
Details
 
Ships in 24 hours
SKU
Retail price: $469.95
Our price:
$446.45
Options
Want this item shipped on December 9? Order within the next 40 hrs 20 mins.
Pump Hanger
Optional Plumbing Kit
DIY Wiring Kit
Quantity

PROPOSITION 65
Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm.

Prop65 WARNING: Cancer and Reproductive Harm. (www.p65warnings.ca.gov)

 

Price match request form

Have you seen this product at a lower price elsewhere? If so, please give us a chance to match or beat it! We will respond to your request promptly!
Your Name: *
Email: *
Phone:  
Competitor's Link/Web Address: *
Competitor's Price: * $ *Please include shipping/handling charges
Additional Comments:  

Terms & Conditions:

 
    I have read and accept the Terms & Condition
 
   

Send to friend

: *
: *
: *
 
 

Customer feedback

There have been no reviews